What do you use for a short steady rest?

Tools, Reviews, how to use, show it off, new purchase, hand tools, power tools, new technologies, routing/bits, jigs/templates, etc...
Post Reply
Cherryville Chuck
Global Moderator
Global Moderator
Posts: 2648
Joined: Mon Oct 05, 2020 8:27 pm
Location: Cherryville, B C
Has thanked: 561 times
Been thanked: 1011 times

What do you use for a short steady rest?

#1

Post by Cherryville Chuck »

I’m curious what other members use for a steady rest when turning short small things like chisel and file handles. I made one years ago by welding a 1” bolt to a short piece of square tube.
You do not have the required permissions to view the files attached to this post.
User avatar
HandyDan
Forum Moderator
Forum Moderator
Posts: 7051
Joined: Mon Oct 05, 2020 7:44 pm
Location: Youngstown, Oh
Has thanked: 378 times
Been thanked: 372 times

Re: What do you use for a short steady rest?

#2

Post by HandyDan »

I have done similar using round stock.

014-1.jpg

I actually made the banjo too.

013-2.jpg

I have also used heavy angle on top too. The angle is better since the round top rest didn't have an offset and was hard to get close to a thin turning. Don't have a picture of those on hand.
You do not have the required permissions to view the files attached to this post.
HandyDan
Youngstown, Oh
Cherryville Chuck
Global Moderator
Global Moderator
Posts: 2648
Joined: Mon Oct 05, 2020 8:27 pm
Location: Cherryville, B C
Has thanked: 561 times
Been thanked: 1011 times

Re: What do you use for a short steady rest?

#3

Post by Cherryville Chuck »

I like the bar idea. I didn't foresee one issue when I went with the tube and that was being able to lever the chisel up and down on it. It's easier to slide along than the stock knife edge rest that came with the machine but that's it's only advantage.

You could take a 3/4 or 1" wide flat bar and weld it to the side of the post too I would think. You'd just need to make certain to get it at 90 degrees to the post. That would get you right against the turning if you wanted.
User avatar
HandyDan
Forum Moderator
Forum Moderator
Posts: 7051
Joined: Mon Oct 05, 2020 7:44 pm
Location: Youngstown, Oh
Has thanked: 378 times
Been thanked: 372 times

Re: What do you use for a short steady rest?

#4

Post by HandyDan »

I have a metal lathe and after I decide what to use for the post I put it in the lathe and square the end. I did get my first one out of square.
HandyDan
Youngstown, Oh
Cherryville Chuck
Global Moderator
Global Moderator
Posts: 2648
Joined: Mon Oct 05, 2020 8:27 pm
Location: Cherryville, B C
Has thanked: 561 times
Been thanked: 1011 times

Re: What do you use for a short steady rest?

#5

Post by Cherryville Chuck »

The home made banjo is a good idea too. I think I've seen a plan for one out of plywood before. Long turnings are another issue. It's nice to have a long steady rest for those but it needs 2 banjos and posts to work well. Angle iron would work well for a long rest. Nice and stiff without being too heavy.
User avatar
Nickp
Site Admin
Posts: 1374
Joined: Mon Oct 05, 2020 6:31 pm
Location: Monroe County, PA
Preferred name: Nick
Has thanked: 533 times
Been thanked: 352 times

Re: What do you use for a short steady rest?

#6

Post by Nickp »

Great idea...!
Don't piss off old people. The older we get the less "Life in Prison" is a deterrent !
User avatar
DaninVan
Registered User
Posts: 2371
Joined: Mon Oct 05, 2020 6:12 pm
Location: Sunshine Coast, BC, Canada
Has thanked: 302 times
Been thanked: 417 times

Re: What do you use for a short steady rest?

#7

Post by DaninVan »

A midget?
User avatar
Stick486
CS/TS
Posts: 20495
Joined: Thu Jan 21, 2021 7:40 am
Location: Central Colorado
Preferred name: Stick486
Has thanked: 657 times
Been thanked: 580 times

Re: What do you use for a short steady rest?

#8

Post by Stick486 »

DaninVan wrote: Tue Jun 21, 2022 9:19 amA midget?
.
1 GROAN BUTTON.jpg
You do not have the required permissions to view the files attached to this post.
Forget the primal scream, just ROAR!!!
SNORK” Mountain Congressional Library and Taxidermy...
Post Reply