Best blade for tracksaw to cut plexiglass

Tools, Reviews, how to use, show it off, new purchase, hand tools, power tools, new technologies, routing/bits, jigs/templates, etc...
Post Reply
User avatar
RainMan
Registered User
Posts: 183
Joined: Mon Jan 10, 2022 8:10 pm
Location: Cranbrook BC
Preferred name: Rick
Has thanked: 56 times
Been thanked: 48 times

Best blade for tracksaw to cut plexiglass

#1

Post by RainMan »

Hey all, my friend is going to use 1/2” plexiglass on the sides of his staircase . I believe it’s NOT lexan . I have to cut 45 degree angles besides the long one to shorten its height , and I figure my festool TS75 tracksaw would be the best option seeing I have to cut angles . The owner of Windsor Plywood thinks I’m overthinking it ,and says to use the factory blade . I think it’s 36 tooth 210mm diameter with a 30 mm arbor , so Freud blades will not fit , at least the ones I’ve seen .
I can change the rpm also and may try slowing it down . Steve the Windsor Plywood owner recommended setting the tracksaw to 1/8” , and do one cut across, then lower the blade and do a final deep cut .
Steve thinks if I buy the blade pictured here , that it will get plugged up having a lot of teeth , so I’m not sure if it’s worth the investment.
Festool also makes a blade for wood finishing , but super expensive.
I’ve been reading all kinds of things about different angles on the teeth that are preferred for plastics , but it’s over my head .
Just wondering what others have had for best results without chipping . I think clamping a sacrificial piece of mdf over the cut may be a nuisance.
I guess doing a test cut would be a good idea to see how it reacts.

Here’s the options I was thinking of but they’re not dedicated to acrylic, although the festool one says laminate , so maybe that would be better?
You do not have the required permissions to view the files attached to this post.
I don’t always insulate , but when I do .
Ok , I never insulate
User avatar
Stick486
CS/TS
Posts: 20493
Joined: Thu Jan 21, 2021 7:40 am
Location: Central Colorado
Preferred name: Stick486
Has thanked: 657 times
Been thanked: 580 times

Re: Best blade for tracksaw to cut plexiglass

#2

Post by Stick486 »

Wood blades average around 40 teeth while plastic blades have around 60. They cut through plastic, acrylic, and soft, non-ferrous metals. For Plexiglas, you’ll want a fine blade with at least 80 teeth.
Cut into plastic and soft materials slowly. If you go too quickly, the material can “catch” on the saw blade, which can damage both the blade and the project. You’ll want to cut with a smooth, pushing motion.

Go w/ a TCG toothed blade w/ a negative rake of 3~5°.... Plan "B" is a HI-ATB toothed blade
Forget the primal scream, just ROAR!!!
SNORK” Mountain Congressional Library and Taxidermy...
Cherryville Chuck
Global Moderator
Global Moderator
Posts: 2648
Joined: Mon Oct 05, 2020 8:27 pm
Location: Cherryville, B C
Has thanked: 561 times
Been thanked: 1011 times

Re: Best blade for tracksaw to cut plexiglass

#3

Post by Cherryville Chuck »

Plastic cutting tooling usually has different geometry from wood cutting. You need something with no hook angle. I've cut laminate sheet and plexi on my TS using a melamine blade and zero clearance insert. Melamine blades have little to negative hook. I have a circ saw blade for cutting vinyl siding and it looks much like an old school steel tooth plywood blade so one of those might work too.
User avatar
Herb Stoops
The Welcome Wagon
Posts: 3054
Joined: Mon Oct 05, 2020 8:05 pm
Location: Auburn WA.,USA
Preferred name: Raff
Has thanked: 1484 times
Been thanked: 876 times

Re: Best blade for tracksaw to cut plexiglass

#4

Post by Herb Stoops »

The problem I have always had with plastic cutting is the build up of the melted sawdust on the teeth using a common wood cutting blade. One article I just read said to set the height of the cut to 1/4" higher than the material,(tablesaw), to give the tooth clearance to clean the shavings from the cut. If you can try a scrap before you make a cut.
The Track saw sounds like an excellent choice,that should keep down any scratching of the finished surface,and has the ability to suck up the sawdust flying around. I always avoided cutting plastic because of the mess it creates.
Herb
User avatar
RainMan
Registered User
Posts: 183
Joined: Mon Jan 10, 2022 8:10 pm
Location: Cranbrook BC
Preferred name: Rick
Has thanked: 56 times
Been thanked: 48 times

Re: Best blade for tracksaw to cut plexiglass

#5

Post by RainMan »

Herb Stoops wrote: Tue Nov 14, 2023 1:13 pm The problem I have always had with plastic cutting is the build up of the melted sawdust on the teeth using a common wood cutting blade. One article I just read said to set the height of the cut to 1/4" higher than the material,(tablesaw), to give the tooth clearance to clean the shavings from the cut. If you can try a scrap before you make a cut.
The Track saw sounds like an excellent choice,that should keep down any scratching of the finished surface,and has the ability to suck up the sawdust flying around. I always avoided cutting plastic because of the mess it creates.
Herb
Yes unfortunately it’s too cold now to do outside . I told my friend to take the plexi and let it sit in his heated basement for a few days to acclimate .
There’s not a lot of room ,but we’ll make do .
I told him the same thing you mentioned, seeing as we need to take a 45 degree chunk off , why not do a test cut first



Cherryville Chuck wrote: Tue Nov 14, 2023 9:33 am Plastic cutting tooling usually has different geometry from wood cutting. You need something with no hook angle. I've cut laminate sheet and plexi on my TS using a melamine blade and zero clearance insert. Melamine blades have little to negative hook. I have a circ saw blade for cutting vinyl siding and it looks much like an old school steel tooth plywood blade so one of those might work too.
That’s interesting, as I was wondering about the angle of the teeth

Stick486 wrote: Tue Nov 14, 2023 6:44 am Wood blades average around 40 teeth while plastic blades have around 60. They cut through plastic, acrylic, and soft, non-ferrous metals. For Plexiglas, you’ll want a fine blade with at least 80 teeth.
Cut into plastic and soft materials slowly. If you go too quickly, the material can “catch” on the saw blade, which can damage both the blade and the project. You’ll want to cut with a smooth, pushing motion.

Go w/ a TCG toothed blade w/ a negative rake of 3~5°.... Plan "B" is a HI-ATB toothed blade
Thanks Stick . I have a feeling sourcing a blade for a tracksaw with more than 60 teeth may be an issue .
Hey are you still up on that mountain?
I don’t always insulate , but when I do .
Ok , I never insulate
User avatar
Herb Stoops
The Welcome Wagon
Posts: 3054
Joined: Mon Oct 05, 2020 8:05 pm
Location: Auburn WA.,USA
Preferred name: Raff
Has thanked: 1484 times
Been thanked: 876 times

Re: Best blade for tracksaw to cut plexiglass

#6

Post by Herb Stoops »

Is this stair going to have panels or one piece from top to bottom ? If it has panels will the vertical joint have have an "H" piece between panels or just an air space? Is the cut edge going to be visible?
Herb
User avatar
RainMan
Registered User
Posts: 183
Joined: Mon Jan 10, 2022 8:10 pm
Location: Cranbrook BC
Preferred name: Rick
Has thanked: 56 times
Been thanked: 48 times

Re: Best blade for tracksaw to cut plexiglass

#7

Post by RainMan »

Herb Stoops wrote: Tue Nov 14, 2023 8:10 pm Is this stair going to have panels or one piece from top to bottom ? If it has panels will the vertical joint have have an "H" piece between panels or just an air space? Is the cut edge going to be visible?
Herb
Yes it’s going to be an exposed edge on the sides . Unfortunately one 4x8 sheet is not long enough , so they have these metal clips that connect the sheets . Going to look kind of weird adding a small piece at the top ,but that’s their plan .
I have cut lexan and 0keci in the past but on my table saw . I used 120 grit sandpaper,then followed it with finer sandpaper to get the cut edges clear again . Actually used toothpaste as a rubbing compound to get it super clear .
I also experimented with a torch to glaze the edges after sanding . Worked well but you have to be careful not to burn and bubble it
I don’t always insulate , but when I do .
Ok , I never insulate
Cherryville Chuck
Global Moderator
Global Moderator
Posts: 2648
Joined: Mon Oct 05, 2020 8:27 pm
Location: Cherryville, B C
Has thanked: 561 times
Been thanked: 1011 times

Re: Best blade for tracksaw to cut plexiglass

#8

Post by Cherryville Chuck »

Even hand sanding you have to be careful not to go too fast and with too much pressure. I'd heard about using toothpaste before.
Biagio
Registered User
Posts: 264
Joined: Thu Oct 29, 2020 12:34 pm
Location: Johannesburg, South Africa
Has thanked: 57 times
Been thanked: 78 times

Re: Best blade for tracksaw to cut plexiglass

#9

Post by Biagio »

I got a fairly decent cut on acrilate using an inexpensive 60T negative rake TCD that is marketed as an aluminium blade. Used my DeWalt cordless saw on an amateurish Wolfcraft track system. White swarf everywhere.
User avatar
Stick486
CS/TS
Posts: 20493
Joined: Thu Jan 21, 2021 7:40 am
Location: Central Colorado
Preferred name: Stick486
Has thanked: 657 times
Been thanked: 580 times

Re: Best blade for tracksaw to cut plexiglass

#10

Post by Stick486 »

Biagio wrote: Wed Nov 15, 2023 2:36 pmnegative rake TCD
.
The negative rake is the best way by far to go... VOE...
Forget the primal scream, just ROAR!!!
SNORK” Mountain Congressional Library and Taxidermy...
Cherryville Chuck
Global Moderator
Global Moderator
Posts: 2648
Joined: Mon Oct 05, 2020 8:27 pm
Location: Cherryville, B C
Has thanked: 561 times
Been thanked: 1011 times

Re: Best blade for tracksaw to cut plexiglass

#11

Post by Cherryville Chuck »

Holding the piece down firmly against the table is important too because if the sheet starts to flutter chances are it will blow up.
Post Reply