Just came across this…
Rust
- Sominus
- Forum Supernumerary
- Posts: 406
- Joined: Mon Oct 05, 2020 5:31 pm
- Location: Houston, TX
- Preferred name: Michael
- Has thanked: 22 times
- Been thanked: 157 times
Rust
You do not have the required permissions to view the files attached to this post.
—
Michael Dow
Houston, Tx
<insert witty saying here>
Michael Dow
Houston, Tx
<insert witty saying here>
- Herb Stoops
- The Welcome Wagon
- Posts: 3054
- Joined: Mon Oct 05, 2020 8:05 pm
- Location: Auburn WA.,USA
- Preferred name: Raff
- Has thanked: 1484 times
- Been thanked: 876 times
- Stick486
- CS/TS
- Posts: 20482
- Joined: Thu Jan 21, 2021 7:40 am
- Location: Central Colorado
- Preferred name: Stick486
- Has thanked: 657 times
- Been thanked: 580 times
Re: Rust
.
did you not remember these???
.
You do not have the required permissions to view the files attached to this post.
Forget the primal scream, just ROAR!!!
SNORK” Mountain Congressional Library and Taxidermy...
-
- Global Moderator
- Posts: 2648
- Joined: Mon Oct 05, 2020 8:27 pm
- Location: Cherryville, B C
- Has thanked: 561 times
- Been thanked: 1011 times
Re: Rust
There are lots of misconceptions about what WD 40 is good for. Breaking nuts free isn't one of them. Using it as a lube isn't either. Truckers here use it it in the winter to get moisture of of electrical connections going to their trailers. It can't be beat for that. It's pretty good for dissolving goo and grime. It has good short term anti corrosion properties for iron and steel, likely due to its ability to displace moisture. I use it once in a while to cool steel down when grinding or drilling. It displaces heat pretty well too.
It's good to see an actual comparison of the Atf mix compared to some well known nut busting products.
It's good to see an actual comparison of the Atf mix compared to some well known nut busting products.
- Stick486
- CS/TS
- Posts: 20482
- Joined: Thu Jan 21, 2021 7:40 am
- Location: Central Colorado
- Preferred name: Stick486
- Has thanked: 657 times
- Been thanked: 580 times
Re: Rust
then it becomes/turns hygroscopic....Cherryville Chuck wrote: ↑Mon Mar 27, 2023 12:59 pm It has good short term anti corrosion properties for iron and steel, likely due to its ability to displace moisture
Forget the primal scream, just ROAR!!!
SNORK” Mountain Congressional Library and Taxidermy...
-
- Global Moderator
- Posts: 2648
- Joined: Mon Oct 05, 2020 8:27 pm
- Location: Cherryville, B C
- Has thanked: 561 times
- Been thanked: 1011 times
Re: Rust
Over what time period?Stick486 wrote: ↑Wed Mar 29, 2023 11:13 pmthen it becomes/turns hygroscopic....Cherryville Chuck wrote: ↑Mon Mar 27, 2023 12:59 pm It has good short term anti corrosion properties for iron and steel, likely due to its ability to displace moisture
- Stick486
- CS/TS
- Posts: 20482
- Joined: Thu Jan 21, 2021 7:40 am
- Location: Central Colorado
- Preferred name: Stick486
- Has thanked: 657 times
- Been thanked: 580 times
Re: Rust
You do not have the required permissions to view the files attached to this post.
Forget the primal scream, just ROAR!!!
SNORK” Mountain Congressional Library and Taxidermy...
-
- Global Moderator
- Posts: 2648
- Joined: Mon Oct 05, 2020 8:27 pm
- Location: Cherryville, B C
- Has thanked: 561 times
- Been thanked: 1011 times
Re: Rust
That doesn't say it becomes hygroscopic over time. It is a good gunk remover. I've been using it with wet and dry carbide sandpaper to remove rust and grunge off old handsaws and planes.A fairly scientifically done corrosion test I saw with at least a dozen other products had it coming in around 4th position and that included over a period of 3 -4 weeks. Some others may last a lot longer. I have some Fluid Film I've been using between irons and chip breakers which seem to be a spot prone to corrosion. it should last a lot longer. WD40 works pretty good for cleaning saw blades too. I use a pizza pan to soak them in it.