Here is a vintage Stanley Dowel machine. They must not have been too popular as I have never seen one before, but that doesn't mean anything. Just thought that maybe other members hadn't either.
HErb
STANLEY No. 77 Dowel Machine
-
Herb Stoops
- The Welcome Wagon
- Posts: 3054
- Joined: Mon Oct 05, 2020 8:05 pm
- Location: Auburn WA.,USA
- Preferred name: Raff
- Has thanked: 1484 times
- Been thanked: 876 times
STANLEY No. 77 Dowel Machine
You do not have the required permissions to view the files attached to this post.
-
Herb Stoops
- The Welcome Wagon
- Posts: 3054
- Joined: Mon Oct 05, 2020 8:05 pm
- Location: Auburn WA.,USA
- Preferred name: Raff
- Has thanked: 1484 times
- Been thanked: 876 times
Re: STANLEY No. 77 Dowel Machine
I would guess that you feed the square blanks into the wheel with the holes and the dowel comes out the end where the crank is. Here are the cutters.
Herb
Herb
You do not have the required permissions to view the files attached to this post.
-
Cherryville Chuck
- Global Moderator
- Posts: 2648
- Joined: Mon Oct 05, 2020 8:27 pm
- Location: Cherryville, B C
- Has thanked: 561 times
- Been thanked: 1011 times
Re: STANLEY No. 77 Dowel Machine
I would agree with how it's operated but I haven't figured out yet where the cutter mounts. I imagine it would have been a little pricey just looking at it.
I bought one from LV that I use to make arrow shafts although at 3/8" they are a tad oversize from what's normal, normal being 5/16 or 23/32". It works like a pencil sharpener. You cut 7/16" blanks and drive them through it with a square hole socket they sell mounted to a drill. It works pretty well but you have to wear a glove to hold it and sometimes hold your other glove inside that one because of the heat generated. I can only do one or two and then have to let it cool down. https://www.leevalley.com/en-ca/shop/to ... on-cutters
I bought one from LV that I use to make arrow shafts although at 3/8" they are a tad oversize from what's normal, normal being 5/16 or 23/32". It works like a pencil sharpener. You cut 7/16" blanks and drive them through it with a square hole socket they sell mounted to a drill. It works pretty well but you have to wear a glove to hold it and sometimes hold your other glove inside that one because of the heat generated. I can only do one or two and then have to let it cool down. https://www.leevalley.com/en-ca/shop/to ... on-cutters
-
Biagio
- Registered User
- Posts: 264
- Joined: Thu Oct 29, 2020 12:34 pm
- Location: Johannesburg, South Africa
- Has thanked: 57 times
- Been thanked: 78 times
Re: STANLEY No. 77 Dowel Machine
How the hell did that company go south? They had such a good pipeline of quality stuff, once upon a time.
-
Herb Stoops
- The Welcome Wagon
- Posts: 3054
- Joined: Mon Oct 05, 2020 8:05 pm
- Location: Auburn WA.,USA
- Preferred name: Raff
- Has thanked: 1484 times
- Been thanked: 876 times
Re: STANLEY No. 77 Dowel Machine
@Cherryville Chuck I have the same from LV, I bought the whole set. I clamp the cutter in the vise and just run the square materiel thru with my battery drill motor and the socket. I like it a little oversize so I can sand it down to remove the cutter marks, It works really good for my dowel hinge boxes.
I agree with Biagio, Stanley was the standard of the industry at one time. I think they made or carried just about every tool at one time. There were brands that were a little better quality and higher priced, and some lower quality and lower priced tool out there, the tradesmen knew that they couldn't go wrong with Stanley.
Herb
I agree with Biagio, Stanley was the standard of the industry at one time. I think they made or carried just about every tool at one time. There were brands that were a little better quality and higher priced, and some lower quality and lower priced tool out there, the tradesmen knew that they couldn't go wrong with Stanley.
Herb
-
Stick486
- CS/TS
- Posts: 20493
- Joined: Thu Jan 21, 2021 7:40 am
- Location: Central Colorado
- Preferred name: Stick486
- Has thanked: 657 times
- Been thanked: 580 times
Re: STANLEY No. 77 Dowel Machine
bean counter for the investors...
Forget the primal scream, just ROAR!!!
SNORK” Mountain Congressional Library and Taxidermy...
-
Cherryville Chuck
- Global Moderator
- Posts: 2648
- Joined: Mon Oct 05, 2020 8:27 pm
- Location: Cherryville, B C
- Has thanked: 561 times
- Been thanked: 1011 times
Re: STANLEY No. 77 Dowel Machine
Thanks for the tip about sticking it in the vise.Herb Stoops wrote: ↑Tue Apr 20, 2021 2:52 am @Cherryville Chuck I have the same from LV, I bought the whole set. I clamp the cutter in the vise and just run the square materiel thru with my battery drill motor and the socket. I like it a little oversize so I can sand it down to remove the cutter marks, It works really good for my dowel hinge boxes.
I agree with Biagio, Stanley was the standard of the industry at one time. I think they made or carried just about every tool at one time. There were brands that were a little better quality and higher priced, and some lower quality and lower priced tool out there, the tradesmen knew that they couldn't go wrong with Stanley.
Herb
Another testament to Stanley is that many of the hand tools we see being made now are based on Stanley's designs.Even Lee Valley's honing guide may be based on a Stanley idea. Remember the plane blade honing guide I sent you Herb? That is essentially how LV's works. The Stanley even came with a built in angle guide.