Some cool measuring tricks…
-
HandyDan
- Forum Moderator
- Posts: 7044
- Joined: Mon Oct 05, 2020 7:44 pm
- Location: Youngstown, Oh
- Has thanked: 378 times
- Been thanked: 372 times
Re: Some cool measuring tricks…
Yep, Pretty cool. Now if I can remember them.
HandyDan
Youngstown, Oh
Youngstown, Oh
-
Stick486
- CS/TS
- Posts: 20483
- Joined: Thu Jan 21, 2021 7:40 am
- Location: Central Colorado
- Preferred name: Stick486
- Has thanked: 657 times
- Been thanked: 580 times
Re: Some cool measuring tricks…
where were you last week????
thanks buddy...
thanks buddy...
Forget the primal scream, just ROAR!!!
SNORK” Mountain Congressional Library and Taxidermy...
-
roxanne562001
- Registered User
- Posts: 200
- Joined: Sun Jan 24, 2021 12:14 pm
- Has thanked: 179 times
- Been thanked: 90 times
-
Nickp
- Site Admin
- Posts: 1374
- Joined: Mon Oct 05, 2020 6:31 pm
- Location: Monroe County, PA
- Preferred name: Nick
- Has thanked: 533 times
- Been thanked: 352 times
Re: Some cool measuring tricks…
I love this stuff...! ! ! Thanks...!
(not that I'll remember it
)
(not that I'll remember it
)Don't piss off old people. The older we get the less "Life in Prison" is a deterrent !
-
Cherryville Chuck
- Global Moderator
- Posts: 2648
- Joined: Mon Oct 05, 2020 8:27 pm
- Location: Cherryville, B C
- Has thanked: 561 times
- Been thanked: 1011 times
-
CharleyL
- Registered User
- Posts: 223
- Joined: Thu Oct 14, 2021 8:47 pm
- Location: Central NC, USA
- Preferred name: Charley
- Has thanked: 83 times
- Been thanked: 129 times
Re: Some cool measuring tricks…
When measuring the spacing of two identical holes to be able to add a third at the same spacing, just measure from one edge of the first hole to the same edge of the second hole. it's the same measurement as center to center, but much easier to get accurately.
Charley
Charley
-
DaninVan
- Registered User
- Posts: 2371
- Joined: Mon Oct 05, 2020 6:12 pm
- Location: Sunshine Coast, BC, Canada
- Has thanked: 302 times
- Been thanked: 417 times
Re: Some cool measuring tricks…
...just don't forget that the mark you made wasn't the C/L of the hole when you drill!CharleyL wrote: ↑Thu Nov 11, 2021 11:24 am When measuring the spacing of two identical holes to be able to add a third at the same spacing, just measure from one edge of the first hole to the same edge of the second hole. it's the same measurement as center to center, but much easier to get accurately.
Charley
-
Nickp
- Site Admin
- Posts: 1374
- Joined: Mon Oct 05, 2020 6:31 pm
- Location: Monroe County, PA
- Preferred name: Nick
- Has thanked: 533 times
- Been thanked: 352 times
Re: Some cool measuring tricks…
There is that...!
Don't piss off old people. The older we get the less "Life in Prison" is a deterrent !
-
Stick486
- CS/TS
- Posts: 20483
- Joined: Thu Jan 21, 2021 7:40 am
- Location: Central Colorado
- Preferred name: Stick486
- Has thanked: 657 times
- Been thanked: 580 times
Re: Some cool measuring tricks…
just in case you need a tape...
.
.
Forget the primal scream, just ROAR!!!
SNORK” Mountain Congressional Library and Taxidermy...
-
CharleyL
- Registered User
- Posts: 223
- Joined: Thu Oct 14, 2021 8:47 pm
- Location: Central NC, USA
- Preferred name: Charley
- Has thanked: 83 times
- Been thanked: 129 times
Re: Some cool measuring tricks…
For that measurement, add 1/2 the diameter of the hole to the above measurement. Again, this only applies to holes of the same diameter.DaninVan wrote: ↑Fri Nov 12, 2021 11:20 am...just don't forget that the mark you made wasn't the C/L of the hole when you drill!CharleyL wrote: ↑Thu Nov 11, 2021 11:24 am When measuring the spacing of two identical holes to be able to add a third at the same spacing, just measure from one edge of the first hole to the same edge of the second hole. it's the same measurement as center to center, but much easier to get accurately.
Charley
Charley